Matek Systems ELRS-R24-P6 R24-P6 ExpressLRS 2.4GHz PWM Receiver With Antenna Support 2~8S VBat Voltage Sense For FPV RC Racing Drone
Direct purchase from the factory 
Oñemo'ã porãva
Jopói libre
Mba'e rembosa'irã
Mba'e devolución reheguaJopói libre
Eg̃uahẽ porã Roymall-pe, ne renda jopói porã joguápe. Rohechakuaa ha roaguyje ne pytyvõ, ha roñe'ẽ aguyje jopói libre ndive. Ejogua vove, rejoguáta mba'eporã porã ha reñemomba'e jopói libre ndive. Eheka ore apopyrã ha ejuhu ne jopói perfecto.Mba'e rembosa'irã
Rojapo tembiapo rembosa'irã 2 ára peve.Ára sapy'agua oñemboare 2 ára.Oñemboare 5-7 ára mba'apo (Lunes a Viernes).Oñemboare sapy'a tetã ambuéva rupi.1. Devolución ha cambio
Roñemoneĩ devolución Roymall-gui añoite. Jopói libre ndojejapói devolución. Ejapo devolución oimeraẽva jopói ojeipurúva'ỹre.Roñemoneĩ devolución 3-5 ára mba'apo peve.Jopói personalizado ndojejapói devolución.Eñe'ẽ ore ndive. service@roymall.com térã Whatsapp: +86193598494712.Devuelta
Reguereko devuelta oimeraẽva jopói ojeipurúva'ỹre. Mba'e rembosa'irã ndojejapói devuelta.Eñe'ẽ ore ndive. service@roymall.com térã Whatsapp: +8619359849471Description:
Brand: Matek Systems
Model: ELRS-R24-P6
Item: PWM Receiver
ESP8285, SX1281
Antenna connector: IPEX MHF 1
6x PWM outputs
Support 2~8S VBat voltage sense
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: 12dbm
Receiver output protocol: PWM
Input voltage: 4~9V DC @ u201c+u201d pad
Voltage sense: 34V Max. @ u201cVBatu201d pad
Power dissipation: 45mA(binding), 85mA(wifi mode)
PCB size: 20mm x 18mm
Weight: 2g w/ antenna
Firmwares
* ExpressLRS 3.0 or newer, DIY 2.4GHz / DIY 2400 RX PWMP EX.
* ExpressLRS wiki for PWM receiver, Click HERE
* Make sure Receiver and TX module both are running ExpressLRS 3.0 or newer.
u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014u2014-
* Receiver has ExpressLRS 3.0 preloaded with binding phrase "123456", the Receiver will never enter binding mode if using the traditional binding procedure.
* You need to reflash it with your binding phrase OR go into WebUI to set your binding phrase.
Flashing via Wifi
* Disconnect ESC and servos from receiver first.
* Power on receiver by 5V source. Receiver"s LED(Red) will blink slow at first, and after 20s, it should blink fast indicating it"s on Wifi Hotspot Mode.
* More detailed steps, pls refer this page.
* Target: DIY 2.4 GHz / DIY 2400 RX PWMP EX.
Flashing via UART
* Disconnect ESC and servos from receiver first.
* Wire the receiver into the USB-TTL adapter, with TX on receiver connected to the Rx on the USB-TTL, and RX on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to 5V and GND of the Receiver.
* Press the boot button while powering on the receiver, then release u2013 the Red LED on receiver should now be solid.
* Select the target DIY 2.4 GHz / DIY 2400 RX PWMP EX and u201cUARTu201d for Flashing Method, set your bind phrase and Firmware Options and once done, click on Build and Flash.
Package Included:
1x Matek Systems ELRS-R24-P6 Receiver
1x IPEX MHF1 Antennas. 15cm
Dupont 2.54 pins (Board is shipped unsoldered)
